Multiple Use AVL GPS Tracker, AVL-300

Multiple Use AVL Tracker GPS Tracking Device

This AVL-300 vehicle tracking device offers multiple options and outstanding durability. The AVL-300 tracker features both real time and passive GPS tracking options, two digital inputs and two analog inputs, including one that may be used as a third digital input.

AVL-300 Features

The GPS tracking device can be easily configured to communicate with a back-end server to provide emergency notifications, low battery alerts, geo-fence alarms, and more. The AVL-300 vehicle tracker is also compatible with Garmin Fleet Management Interface (FMI) protocol. Additional cables are required for this application. The vehicle tracker is also equipped with a built-in GPS/GSM antenna, and is compatible with optional external antennas.

The AVL-300 tracker is equipped with a UBlox chipset for faster time to first fix (TTFF) and greater accuracy, and eliminates problems caused by GPS jammers with a built-in jammer detection feature. For greater efficiency, the device includes a built-in 3D motion sensor for conserving power and the advantage of detecting motion of the tracked vehicle. The AVL-300 tracker is compatible with a wide range of operating voltages, from 8-32 V DC.

AVL-300 Specifications

GSM Specifications
Frequency	Quad-Band: 850/900/1800/1900MHz Compliant to GSM Phase 2/2+ -Class 4 (2W @ 850/900MHz) -Class 1 (1W @ 1800/1900MHz)
GPRS	GPRS multi-slot class 12 GPRS mobile station class B
RMS Phase Error	5 deg
Max Out RF Power	33.0dBm ± 2dBm
Dynamic Input Range	-15 ~ -102 dBm
Receiving Sensitivity	Class II RBER2%(-102dBm)
Stability Of Frequency	Greater than 2.5 ppm
Max Frequency Error	± 0.1 ppm
GPS Specifications
GPS Chipset	UBlox. All-In-One receiver. Sensitive Fast and Accurate
Sensitivity	Autonomous: -148 dBm Hot Start: -160 dBm Tracking: -162 dBm
Position Accuracy	Without Aid: 3.0 m 2D-RMS DGPS: 2.5 m
TTFF (Open Sky)	Cold start 30s average Warm start <30s Hot start <1.2s
Interfaces
Digital Inputs	Three digital inputs. One positive trigger for ignition detection. Two negative trigger inputs for panic button or other use.
Configurable Inputs	One special input can be configured to negative trigger digital input or analog input (0-2.8V)
Analog Input	One analog input (0-2.8V)
Digital Output	Two digital outputs, open drain, 150mA drive current max
Latched Digital Outputs	One digital output with internal latch circuit, open drain, 150mA drive current max
Two-Way Audio	Speaker and Microphone on 16 PIN connector
GSM Antenna	Built in
GPS Antenna	Built in or external (Optional, SMA RF connector)
Serial Port	On MINI-USB for firmware upgrading and configuration
General Specifications
Dimension	80mm * 49mm * 26mm
Weight	89 g
Backup Battery	Li-Polymer 250 mAh, 3.7V
Standby Time	Without reporting: 22 to 28 Hours 5 minute reporting: 10 to 12 Hours 10 minute reporting: 12 to 15 Hours
Operation Voltage	8 to 32V DC
Operation Temperature	-30℃ ~ +80℃(Without Battery) -40℃ ~ +85℃ for Storage(Without Battery)
Power Management	Full power pathing; Internal battery is not used when external power is available
Air Interface Protocol
Transmit Protocol	TCP, UDP, SMS
Scheduled Timing Report	Position reports at pre-set time and distance intervals
Geo-Fence	Geo-Fence alarm and parking alarm
Low Power Alarm	Alarm when internal battery is almost exhausted
Power On Report	Report when the device is powered on
Tow Alarm	With built in motion sensor
Antenna Disconnect Alarm	Alarm when the external GPS antenna is disconnected
Special Alarm	Special alarm based on the digital/analog inputs
Remote Control	Control the digital outputs through air interface protocol