433MHZ Wireless Auto-dial Alarm System

This hot new 433Mhz alarm system gets two thumbs up for its high stability and intelligent sound and light alarm system. It uses advanced signal processing technology to ensure unit stability and quick response. This unit is sophisticated but can be set up in less than 15 minutes. The alarm system comes with two wireless remote controls ,a wireless infrared detector, magnetic door/window alarm, an outdoor siren and an indoor siren. And you can add up to 38 sensors/monitors to the unit. That means if you have more areas to monitor just buy extra sensors for those additional areas, up to 38 areas, door and or windows!

Watch Video Below for System Demonstration:





Features:

• 433MHz wireless alarm signal transmission in case of wire installation trouble and expense.
  
• Will Dial telephone or cell phone automatically when protected area is breached.
  
• Also works as a recorder.
  
• Up to 38 accessories (such as remote controls and transmitters) can be used in the system.
  
• Compared with similar products, this system adds a wireless outdoor siren. This siren can be optionally placed outside the home so that when the alarm is activated, a loud siren with flashing light will go off and attract the attention of your neighbors and frighten away the intruders.
• The main unit can be hidden or locked away for added security.
  
• Easy installation of this system gives this system a leg up over other similar products.
  
• Working distance is above 60m in open area.
  
• R6 is remote control. It can wirelessly turn the main unit on/off.
  
• R2 is indoor siren. It will sound an alarm immediately as soon as a signal from the main unit is received.
  
• R7 is outdoor siren. It will sound an alarm immediately as soon as a signal from the main unit is received.
  
• R23 is repeater. It can make the working distance longer between transmitters and receivers.
  
• R25 is code arm & disarm controller and magnetic sensor. It can arm or disarm the whole system by code and delay the time the alarm goes off if needed. When the unit is disarmed with code, its signal transmission will stop.
  
• RL-0503F adopts GPRS wireless transmission technology. It can dial the phone number to make without the need of a telephone line. It can arm or disarm and monitor the system from a distance.

Download Manual Here

This product is suitable for family housing, real estate villas, factories, shopping malls, warehouses and other similar places.

Quick Operation Guide: Refer to numbered picture below

Operating this unit could not be easier. Below is a quick guide. Unpack box Install batteries in units. You will need AAA and AA batteries. Now lets set up the base unit First turn on the main unit [item 1] using the switch on the left side of unit To add a telephone number for auto-dial press the "*" key then enter 1 and the phone number you wish to have dialed incase of emergency. Make sure you include the area code. Then press the # key to confirm and save the phone number. Repeat this to enter up to SIX phone numbers. IMPORTANT: Make sure for testing purposes you enter a telephone number other than the one you are connecting unit to so that the test will work to ensure your unit has been properly set up and is working well. Now connect unit to your telephone base unit using the included adaptor. It is important that you connect this properly. It should be easy to do. Recording a message that will be played when a number is dialed. To record a message hold the REC button on the main unit until you hear a "BEEP". Again hold down the REC button until you hear a BEEP After the BEEP sound record your message. For example "There is an intruder at Jacks house at 123 main street, anytown, NY" or whatever you want to say. Then press the REC button again or wait for a few more seconds and you will hear another been. This will save and confirm the recording. The unit will only do a 25 ssecond recording, no longer. Setting up sensors As mentioned in the beginning make sure you have inserted alkaline batteries into sensors and alarms Turn unit 3 around to the back and press code button. It will sound briefly. Unit 2 does not require anything done after batteries have been inserted. It will be controlled on/off by the base unit You can set these units into their permanent locations or wait until after the test confirms that they all work before nailing or sticking them into their permanent positions. Setting up the remote controllers. This is easy. There is a paper wedge that sticks out of the remote controls. Pull them out so that the batteries inside will make contact and turn them on. That's about all you need to do for the remotes. The remote is all you need to arm and disarm alarm system. You will get two with the package. Testing the unit To ensure unit is functioning we will now do a quick test. On the remote there are 3 buttons; ALARM, ON and OFF. Press the ALARM button. Get ready here there will be lights and loud sirens going off. It will totally feel confusing! It is loud! What this test will do is to cause alarms to go ff as if unit has been activated and that will cause unit to start dialling the number or numbers that you have encoded into the base unit. Have the first number you entered so that you can listen in to ensure that your set up is correct. Final Installation Now that you have tested your unit, and if all works, install the pieces to their permanemnt locations around the house. Now that was not rocket science!